Products \ Cleaning agents

Intended use: Concentrated foamless agent indented for dilution on ceramic and granite surfaces. It is suitable for postconstruction cleaning, while achieving excellent results immediately after the first use. It effectively acts on cement residues, clays after decoration, cement blooms, magnesium and mineral deposits - water rust or urine stone. It should not be used for non-acid-resistant materials (marble, traverine, and the like).

Application: Before starting the work, is it suitable to wash the surface with clean water. Then, apply the diluted preparation using a mop, machine, or sprayer (dilution should be selected according to the degree of surface pollution). Allow the preparation to act for a while (5-10 min.), and then scrub the surface up intensively. After removal of impurities, it is necessary to wash the surface several times with clean water. Finally, it is suitable the surface with a weak detergent solution. Repeat the process as appropriate. Finally, polish the surface with a fine cloth. When working with the concentrate, the use of protective equipment is recommended.

Intended use: Cleaning agent intended for cleaning and polishing of surfaces in one working step. It is intended, in particular, for surfaces prone to damage and gelatinizing, such as polished marbles, granites, as well as natural and artificial stones. It contains very fine and neutral tensides, which effectively also remove resistant impurities. It can also be used for plastic materials. The surface must always be thoroughly washed with clean water. The product is intended either for direct use or for dilution.

Application: Cleaning on floor surfaces is carried out manually, using a mob, or floor washing machine. While maintaining the window sills, worktops, bars, and the like, it is suitable to use a sprayer and a micro-fibre cloth. Other suitable aids include small sponges with a white or red pad, as well as micro-fibres. Finally, wash the surface thoroughly with water. While handling the preparation, the use of protective equipment is necessary.

Intended use: Concentrated foamless agent, intended for dilution and industrial cleaning of all hard floor surfaces resistant to water and aklali, such as PVC, linoleum (including waxed one), glazed and unglazed floor tiles, granite, marble and limestone surfaces, terraces, brick and concrete surface, including poured floors, rubber floors, sports floors, halls, varnished parquets and lumber. The preparation is safe for the surfaces being treated.

Application: Cleaning of floor surfaces is carried out manually using a mop, floor wasching automatic machine, or floor wheel machine with a brush, or pad (it is selected according to the surface type). It is recommended to wash the surface periodically with chlean water. While handling the preparation, the use of protective equipment is necessary.

Intended use: The material of gel consistency is to applied with a rubber spatula to required areas, and residues of softened epoxy is to be removed after a longer action using a plastic spatula. The material is to be applied fully concentrated.

Application: The surface to be cleaned must be washed first in the usual way. The removal of dried residues should be first tried on a small, less visible piece of area; the area on which the residues will be removed subsequently. Testing and removal of residues should be performed only manually, using a cloth, or a brush dampened in a removing agent (remover). Apply the uniform layer of the preparation on the surface being cleaned, and let it to act for appr. 1-10 minutes, then remove the preparation and epoxy residues with a cloth, or a plastic spatula. If the epoxy residues form a thick layer, the whole cycle can be repeated until all epoxy residues are removed. Caution: Do not pour the remover directly on the surface; it could result, for example, in the excessive removal of protective films and waxes, or at the worst, also to damage of surfaces (in mishandling the preparation). While handling the preparation, the use of protective equipment is necessary.

Intended use: The material of gel consistency is to be applied with a brush on silicone residues. After the longer action, the excess swollen material can be scraped away with a plastic spatula.

Application: Apply the undiluted preparation by brush into the joint being cleaned, and let it to act there for a longer period of time. Scrape away the swollen residues of silicone material from the surface with a plastic smoother. In doing so, apply a sufficient pressure. After mechanical cleaning, remove the residues from the joint by washing with water. While handling the cleaning agent, the use of protective equipment is recommended.

Intended use: This preparation is specially intended for impregnation of non-porous materials. It creates a protective layer on surfaces of non-porous materials, and this layer prevents the inrush of water and oils. It is used as prevention of spot creation (red wine, coffee) on polished vitrified ceramic floor tiles. It facilitates the removal of graffiti. Application is to be performed in two layers. The spreading capacity is specified only for 1 layer. This product is intended for non-absorbent materials, for example, ceramic polished floor tiles exposed to heavy pollution, worktops of kitchen units, table tops, window sills, mantel-pieces, etc.

Application: Before application of impregnation, the surface should be washed with a suitable cleaning agent, neutralised with water, and let to dry thoroughly. Impregnation is to be applied using a floor wasching machine or a floor wheel machine with a brush or pad, or manually with a mop and use of a maintenance cart or bucket. Apply the adequate layer of immpregnation unevenly, and rub or apply it with a sponge so that the surface is only humid. The preparation is to be applied at a time only on smaller surfaces, so it is not necessary to come on the wet surface. It is recommended to apply gradually strips of 1,5 m in width, or surfaces of appr. 2-4 m2. Impregnation will be soaked after appr. 5 minutes. It is suitable to apply the second layer after appr. 60 minutes. If the machine is used for application of preparation, the surface should be polished after drying, using a single-wheel floor machine with a high speed, and a pad from natural fibres. After approx. 2 hours, the impregnated surface is a final walking surface and it is possible to test its water resistance - if water soaks, impregnation must be complemented. The whole surface can be loaded not sooner than after 6 hours, and washed after 24 hours. While handling the preparation, the use of protective equipment is necessary.